Avdel GenesisG2-s Manuel d'instructions

Genesis®G2LB2Hydro-Pneumatic Power ToolInstruction Manual

10Nose AssembliesIMPORTANTAir supply must be disconnected when fitting or removing nose assemblies• Fit Locking Ring 8 onto the Chuck Collet Adaptor.•

11Stem DeflectorADAPTOR NUT71210-20101STEM DEFLECTOR07340-00342KIT PART NUMBER: 71210-20100The stem deflector is a very simple alternative to the stan

12• Check for air leaks. If damaged, hoses and couplings should be replaced.• If there is no filter on the pressure regulator, bleed the air line to c

13Servicing the ToolMolykote®55m Grease Safety DataMolykote®111 Grease Safety DataFirst AidSKIN:Flush with water. Wipe off.INGESTION:No first aid shou

14The airline must be disconnected before any servicing or dismantling is attempted unless specifically instructed otherwise.It is recommended that an

15Assemble in reverse order to dismantling noting the following points:• Place Lip Seal 8 onto the insertion rod* ensuring correct orientation. Push t

16General Assembly of Base Tool 71255-02000B - B6665378485868738403983313334AA44453635BB1 3 4 9105 83130324648674750492673702872 1617181420 2122252411

17Parts List for 71255-020000103040506070809101113141617182021222324252628303132333435363738394041424445464707610-0050171230-0201571230-0330071210-021

18PrimingOil DetailsHyspin®VG 32 Oil Safety DataPriming KitTo enable you to follow the priming procedure opposite, you will need to obtain a priming k

19IMPORTANTDISCONNECT THE TOOL FROM THE AIR SUPPLY OR SWITCH OFF AT VALVE 55. REMOVE NOSE ASSEMBLY.All operations should be carried out on a clean ben

20Fault DiagnosisSymptom Possible Cause Remedy Page RefItem numbers in bold refer to the General Assembly drawing and Parts List on pages 16-17.More t

21Notes

22Notes

23Declaration of ConformityWe, Avdel UK Limited, Watchmead Industrial Estate, Welwyn Garden City, Herts, AL7 1LYdeclare under our sole responsibility

Manual No. Issue Change Note No. DateA 04/065 06/04B 07/044 02/07B2 07-103 03/07B3 08-096 07/0807900-00834www.avdel-global.com© 2008 Acument Intell

3Safety Rules 4SpecificationsTool Specification 5Tool Dimensions 5Intent of UsePart Numbering 6Putting into ServiceAir Supply 7Operating Procedure 7No

4Safety Rules1 Do not use outside the design intent.2 Do not use equipment with this tool/machine other than that recommended and supplied by Avdel UK

5Dimensions in millimetres.22312111012015030514511670212°30'Air Pressure Minimum - Maximum 5-7 bar (72.5 - 101.5 psi)Free Air Volume Required @ 5

6G2LB is a hydro-pneumatic tool designed to place Avdel Avdelok®/Maxlok®fasteners at high speed making it ideal for batch or flow-lineassembly in a wi

7All tools are operated with compressed air at an optimum pressure of 5.5 bar. We recommend the use of pressure regulators andautomatic filtering syst

8AVDELOK ®NOSE ASSEMBLY1 In inches then in millimetresNOSE ASSEMBLY part nº71230-05010 for 4.8 (3/16 ") Avdelok®NOSE ASSEMBLY part nº 71230-0502

9Fitting Instructions Avdelok®• Assemble Chuck Jaws 6, Spring Guides 7 and Spring 8 into Chuck Collet 5. (Lightly coat Chuck Jaws and Chuck Collet int